Graco Heat Pump 237578 User Manual

Instructions-Parts List  
Elevators and  
Pump Supports  
306287W  
EN  
Used to raise and lower select Graco circulation and supply pumps. For professional use  
only.  
200 psi (1.4 MPa, 14 bar) Maximum Air Input Pressure  
Important Safety Instructions  
Read all warnings and instructions in this  
manual. Save these instructions.  
See page 2 for a list of models.  
06529b  
06523b  
 
Warnings  
Warnings  
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-  
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When  
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific  
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where  
applicable.  
WARNING  
EQUIPMENT MISUSE HAZARD  
Misuse can cause death or serious injury.  
Do not operate the unit when fatigued or under the influence of drugs or alcohol.  
Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-  
ponent. See Technical Data in all equipment manuals.  
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all  
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about  
your material, request MSDS from distributor or retailer.  
Do not leave the work area while equipment is energized or under pressure.  
Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.  
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufac-  
turer’s replacement parts only.  
Do not alter or modify equipment. Alterations or modifications may void agency approvals and create  
safety hazards.  
Make sure all equipment is rated and approved for the environment in which you are using it.  
Use equipment only for its intended purpose. Call your distributor for information.  
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.  
Do not kink or over bend hoses or use hoses to pull equipment.  
Keep children and animals away from work area.  
Comply with all applicable safety regulations.  
MOVING PARTS HAZARD  
Moving parts can pinch, cut or amputate fingers and other body parts.  
Keep clear of moving parts.  
Do not operate equipment with protective guards or covers removed.  
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,  
follow the Pressure Relief Procedure in your separate pump manual and disconnect all power  
sources.  
306287W  
3
 
Installation  
Installation  
General Information  
NOTE: Reference numbers and letters in parentheses  
in the text refer to the callouts in the figures and the  
parts drawing.  
40  
NOTE: Always use Genuine Graco Parts and Accesso-  
ries, available from your Graco distributor. If you supply  
your own accessories, be sure they are adequately  
sized and pressure rated for your system.  
14 or 28  
To reduce the risk of serious injury, including fluid  
injection, splashing in the eyes or on the skin, or  
injury from moving parts:  
17  
1. Always relieve air and fluid pressure in the pump  
before raising the elevator.  
06523b  
FIG. 1  
2. Keep your fingers and hands away from moving  
parts when raising or lowering the elevator to pre-  
vent pinching or amputating them including  
between the drum and pump mounting assembly.  
3. When the pump is in the raised elevator position,  
do not leave it unattended. Keep air supplied to the  
elevator. Block the pump, drum cover or pump  
support bracket before working on the pump.  
0.25 in  
(6.4 mm)  
Level  
4. Before working on the elevator, remove the pump  
and relieve air pressure to the elevator.  
Raised: 94 in  
(2390 mm)  
Fixed Mount Elevator  
Shim  
Locate the elevator where there is at least 9 ft (2.75 m)  
overhead clearance. Mark and drill holes for 0.5 in. (13  
mm) mounting bolts. See FIG. 2 and the dimensional  
drawing on page 15. Level the base (17), using shims if  
necessary. Secure the base to the floor using four 1/2  
in. (13 mm) mounting bolts which are long enough to  
prevent the elevator from tipping.  
0.5 in (13mm) bolt  
Lowered: 55 in  
(1400 mm)  
06530  
FIG. 2  
4
306287W  
 
Installation  
Pump Support Bracket  
Air Connection  
Set an open drum against the elevator base (17). Posi-  
tion the bracket (40) on top of the drum so that the  
clamp (34) recesses are tight against the elevator riser  
tube (14 or 28). See FIG. 1 and FIG. 3. Raise the riser  
tube up about 0.25 in. (6.4 mm), install the clamps (34)  
and tighten securely. Attach the pump mounting brack-  
ets (38)  
Screw the restrictor valve (55) into the push-pull valve  
(60) as shown in FIG. 5. Mount the valve on the wall at a  
convenient height, using the mounting bracket (54).  
Connect the master air supply to the valve. Screw the  
elbow fitting (52) into the 1/8 npt(f) inlet of the restrictor  
valve. Push one end of the copper tube (51) into the  
elbow and tighten the fitting. Screw the straight fitting  
(53) into the base (17) of the elevator. Push the other  
end of the copper tube (51) into this fitting and tighten  
the fitting.  
Pump Support  
Ref. No. 31  
Push-Pull Valve  
Ref. No. 60  
34  
40  
38  
54  
60  
55  
06528  
FIG. 3  
52  
Cover Support  
Place the cover in its proper position in the support ring  
(49) and tighten the capscrews (45). Set an open drum  
against the elevator base (17) and put the cover on the  
drum so the support clamp (44) recesses are tight  
against the elevator riser tube (14 or 28). Raise the tube  
0.25 in. (6.4 mm), then tighten the clamp screws (42).  
See FIG. 4.  
51  
06531  
FIG. 5  
14 or 28  
49, 45  
49  
45  
48  
44, 42  
17  
06529b  
FIG. 4  
306287W  
5
 
Operation  
Operation  
Starting and Adjusting the  
Elevator  
Changing Drums  
Moving parts can pinch or amputate your fingers.  
When the pump is operating and when raising or  
lowering the elevator, keep your fingers and hands  
away from the elevator, pump support, drum cover,  
and lip of the drum.  
Moving parts can pinch or amputate your fingers.  
When the pump is operating and when raising or  
lowering the elevator, keep your fingers and hands  
away from the elevator, pump support, drum cover,  
and lip of the drum.  
NOTICE  
You must adjust the elevator to ensure that the cover is  
supported by the drum.  
Shortened or recycled drums may cause the pump or  
agitator to bottom out in the drum, causing damage.  
Contact your fluid supplier to order a standard size  
drum.  
1. Close all air regulators and air valves.  
2. Open the main air bleed valve. Pull up on the air  
control valve and let the elevator rise to its full  
height. Normal operation requires only a few sec-  
onds for air pressure to build up or exhaust, and to  
start raising or lowering the elevator.  
1. Stop the pump. Close the pump air bleed valve.  
2. Pull up on the air control valve to raise the elevator.  
3. Remove the empty drum and place the full drum  
against the elevator base.  
3. Set a full 200 liter (55 gal.) drum against the elevator  
base.  
4. Lower the elevator. See Starting and Adjusting  
the Elevator.  
4. With your hands away from the drum and the cover,  
push down on the air control valve and lower the  
elevator until the cover rests on the lip of the drum.  
The support clamp recesses must be tight against  
the elevator riser tube.  
5. Raise the elevator 1/4 in. (6.4 mm), then tighten the  
support clamp screws. This ensures that the cover  
rests on the drum lip when the elevator is in the low-  
ered position.  
6. Before operation, ensure that all fasteners and tube  
connections are tightened securely.  
NOTE: To increase or decrease the operating speed of  
the elevator, loosen the hex nut of the restrictor valve  
and turn the valve needle either in or out.  
6
306287W  
 
Service  
Service  
Lubrication  
Seals and Gaskets  
Every two to six weeks, take the cap (20) off the riser  
tube (14 or 28) and put a few drops of light, high grade  
motor oil on the inside surface of the tube to lubricate  
the leather packing (10). See FIG. 6. When replacing the  
cap, torque to 20-40 ft-lb (37-54 N•m).  
To replace the leather cup packings (10), screw the  
bearing housing (25) out of the riser tube (14 or 28) and  
slide the tube up off the piston (11). See FIG. 6. Screw  
the piston retainer capscrew (21) out of the piston body  
and remove the parts. Inspect parts for wear and dam-  
age and replace as necessary.  
NOTICE  
NOTE: When replacing packings, install a new spreader  
(5). This will increase the life of the packings.  
Be careful not to dent or damage the riser tube (14 or  
28). Dents may cause the elevator to bind, making  
operation impossible.  
Soak new leather packing (10) in light oil, and put lithium  
grease on the inside surface of the tube. Re-assemble  
in the reverse order. Apply Loctite® 542 thread sealant  
to the internal threads of the piston body (11) and the  
threads of the capscrew (21). Torque the capscrew to  
15-20 ft-lb (20-27 N•m).  
Torque to 20-40 ft-lb (27-54 N•m)  
Torque to 15-20 ft-lb (20-27 N•m)  
Torque to 90-130 ft-lb (122-175 N•m)  
Torque to 30-60 ft-lb (40-80 N•m)  
Apply lubricant to inside surface  
Apply tape  
1
2
3
4
5
6
7
To replace the guide tube gasket (19), screw the guide  
tube (13 or 29) out of the elevator base (17). Take the  
gasket out. See FIG. 6. Be careful not to damage the  
outside bearing surface of the guide tube. Put a new  
gasket into the base. Put PTFE tape on the threads of  
the guide tube and screw it into the base. Torque to  
90-130 ft-lb (122-175 N•m).  
®
Apply Loctite 542 Sealant to threads  
Push-Pull Valve  
2
7
21  
1
20  
Remove the valve guide (71), washer (64), o-ring (66*)  
and seal (67*). Pull the assembled valve parts out of the  
valve body (70). See the Parts Drawing on page 10. Dis-  
assemble parts, clean and inspect. Re-assemble the  
valve, using new parts as necessary.  
8
10  
5
4
12 or 24  
9 or 18  
3
6
13 or 29  
5
14 or 28  
19  
4
7
25  
17  
06532  
FIG. 6  
306287W  
7
 
Parts  
Parts  
Elevator  
®
Torque to 90-130 ft-lb (122-175 N•m)  
Apply Loctite TL-222 to threads  
1
2
3
4
5
6
7
8
®
Torque to 30-60 ft-lb (40-80 N•m)  
Torque to 20-40 ft-lb (37-54 N•m)  
Torque to 15-20 ft-lb (20-27 N•m)  
Apply Loctite 542 Sealant to threads  
Apply tape  
Apply lubricant to inside surface  
6
3
3
20  
7
9 or 18  
15  
*30  
1
11  
8
6
14 or 28  
16 or 27  
4
21  
4
8
26  
5*  
5
2
25  
10*  
12  
7
1
29 or 13  
24  
19*  
31  
6524b  
17  
8
306287W  
 
Parts  
Elevator - Parts List  
Model 204385, Series D (see page 8)  
Standard Elevator with Fixed Mounting  
Includes items 3-17, 19-21, 25-26, 30, 31 below  
Model 205332, Series B (see below)  
Bare Elevator  
Includes items 1-17 below  
Ref.  
No. Part No. Description  
Model 207408, Series C (see page 8)  
Heavy Duty Elevator with Fixed Mounting  
Includes items 3-8, 10-11, 15, 17-21, 24-31 below  
Qty.  
1
203743 VALVE, restrictor; includes items  
56- 59 on page 11  
1
2
3
4
5
6
7
8
9
205333 CAP, elevator mounting  
205334 TUBE, elevator riser  
100155 NUT  
150179 PACKING, cup; leather  
156306 WASHER, flat  
158109 GASKET; rubber  
164246 CAP, tube air  
164247 TUBE, guide, elevator  
1
1
1
1
1
1
1
1
1
1
1
Ref.  
No. Part No. Description  
Qty.  
3
100139 PLUG, pipe; 1/8 npt  
1
1
1
1
1
1
4
100422 LOCKWASHER, int shkprf; 3/4”  
150230 SPREADER, packing  
155899 GASKET, rubber  
156306 WASHER, back-up  
157633 SPRING, helical compression  
(Model 204385)  
5*  
7*  
8
10 164248 SPACER  
11 164249 PISTON  
12 169969 FITTING, quick disconnect; 1/8  
npt(m)  
15 159840 ADAPTER; 1/4 npt(f) x 1/8 npt(m)  
16 100030 BUSHING; 1/4 npt(m) x 1/8 npt(f)  
17 16T421 ADAPTER, pipe hex; 1/8 npt (mxf)  
9
10*  
11  
12  
13  
14  
15  
16  
17  
158260 PACKING, cup; leather  
192198 BODY, piston  
1
1
1
1
1
1
1
1
1
1
1
158262 BEARING, piston (Model 204385)  
158263 TUBE, guide (Model 204385)  
158264 TUBE, riser (Model 204385)  
158265 WASHER, special plain  
158267 TUBE, stop (Model 204385)  
158270 BASE, stationary (Model 204385  
and 207408)  
15  
1
16  
12  
17  
18  
158388 SPRING, helical compression  
(Model 207408)  
158429 GASKET, copper  
1
8
7
10  
19*  
20  
21  
24  
25  
26  
27  
28  
29  
30*  
31  
1
1
1
1
1
1
1
1
1
1
1
161320 CAP, tube  
192199 SCREW, special cap  
167870 GUIDE, riser tube (Model 207408)  
167871 HOUSING, elevator bearing  
167872 BEARING, PTFE tape  
167873 TUBE, stop (Model 207408)  
167874 TUBE, riser (Model 207408)  
167875 TUBE, guide (Model 207408)  
722834 PACKING, o-ring  
4
6
5
11  
3
16T421 ADAPTER, pipe hex; 1/8 npt (mxf)  
*Recommended spare parts. Keep on hand to  
reduce down time.  
9
2
9427b  
306287W  
9
 
Parts  
Support and Control  
Ref. No. 31: 206232 Pump Support Assembly  
Screw firmly against seat, back off 1/4 turn  
Apply adhesive  
1
2
40  
34  
32  
32  
39  
37  
33  
Ref. No. 41: 207562  
Cover Support Assembly  
36  
35  
44  
43  
46  
33  
42  
38  
49  
06525  
45  
47  
48  
06526  
62  
Ref. No. 50: 207561 Air Control Kit  
*61  
*69  
73  
70  
54  
58  
*57  
59  
1
65  
68  
56  
2
72  
52  
67*  
1/8 npt  
66  
64  
71  
51  
63  
53  
06527  
10  
306287W  
 
Parts  
Support and Control - Parts List  
Ref.  
No. Part No. Description  
Ref.  
No. Part No. Description  
Qty.  
Qty.  
1
52  
100112 FITTING, 90°male elbow; 0.25”  
(6.4 mm) tube, 1/8 npt  
1
31  
206232 PUMP SUPPORT ASSEMBLY  
Includes items 32- 40  
53  
100113 FITTING, straight; 0.25” (6.4 mm)  
tube, 1/8 npt  
1
32  
33  
34  
100057 SCREW, hex hd cap; 5/16-18 x 3/4”  
100214 LOCKWASHER, spring; 5/16”  
158271 CLAMP, tube; support ring and  
bracket  
8
12  
2
54  
55  
154634 BRACKET, mounting  
203743 VALVE, restrictor  
Includes items 56-59  
1
1
35  
36  
37  
38  
39  
40  
41  
100133 LOCKWASHER, spring; 3/8”  
100469 SCREW, hex hd cap; 3/8-16 x 3/4”  
100538 SCREW, hex hd cap; 5/16-18 x 1/2”  
166573 BRACKET, pump mounting  
166574 STRAP, support bracket  
206762 FRAME, support, pump  
207562 COVER SUPPORT ASSEMBLY  
Includes items 42-49  
4
4
4
2
4
1
1
56  
57*  
58  
59  
60  
101448 NUT, hex jam; 3/8-24  
157628 PACKING, o-ring  
160162 BODY, valve  
160163 NEEDLE, valve  
202295 VALVE, push-pull  
Includes items 61-73  
1
1
1
1
1
61*  
62*  
63  
100272 LOCKWASHER, int shkprf, no. 6  
104560 SCREW, pan hd mach; 6-32 x 3/8”  
154519 KNOB  
1
1
1
1
1
1
1
1
1
1
1
1
1
42  
43  
44  
100057 SCREW, hex hd cap; 5/16-18 x 3/4”  
100214 LOCKWASHER, spring; 5/16”  
158271 CLAMP, tube; support ring and  
bracket  
4
4
2
64  
154526 WASHER, special plain  
154570 WASHER, special plain  
154594 PACKING, o-ring  
155500 SEAL, o-ring  
155811 SEAL, flat cup; air intake  
155921 SEAL, flat cup; air exhaust  
157160 BODY, valve  
65*  
66*  
67*  
68*  
69*  
70  
45  
46  
47  
48  
49  
50  
100022 SCREW, hex hd cap; 1/4-20 x 3/4”  
100181 NUT, square; 5/16-18  
100268 SCREW, rd hd mach; 10-24 x 3/8”  
202776 BRACE, support  
202777 RING, support  
207561 KIT, control, air  
2
4
2
1
1
1
71  
72  
73  
157161 GUIDE, valve  
161129 STEM, large round; air intake  
161132 STEM, small square  
Includes items 51-73  
057024 TUBE, copper; 0.25” (6.4 mm)  
tube, 5 ft (1.52 m)  
51  
1
*Recommended spare parts. Keep on hand to  
reduce down time.  
306287W  
11  
 
Parts  
Support and Control  
(Models 237746 Series A, 241663 Series A, 237579, 237578)  
Model 237746, Series A  
Standard Elevator with Fixed Mounting  
Includes 204385 Elevator (see page 8), 237579 Air Control Kit, and 237578 Cover Support Assembly  
Model 241663, Series A  
Standard Elevator with Fixed Mounting  
Includes 204385 Elevator (see page 8), 207561 Air Control Kit (see page 10), and 207562 Cover Support Assembly  
(see page 10)  
237579 Air Control Kit  
Includes items 101-111  
237578 Cover Support Assembly  
Includes items 201-216  
106  
101  
Drum cover is not included.  
See page 8 for parts.  
1
2
103  
2
204  
211  
215  
208  
202  
214  
209  
203  
102  
105  
106  
110  
103  
215  
216  
111  
108  
208  
206  
104  
102  
(REF)  
201  
207  
109  
205, 210,  
212, 213  
1
06217b  
12  
306287W  
 
Parts  
Support and Control- Parts List  
(Models 237746 Series A, 241663 Series A, 237579, 237578)  
Model 237746, Series A  
Standard Elevator with Fixed Mounting  
Includes 204385 Elevator (see page 8), 237579 Air Control Kit, and 237578 Cover Support Assembly  
Model 241663, Series A  
Standard Elevator with Fixed Mounting  
Includes 204385 Elevator (see page 8), 207561 Air Control Kit (see page 10), and 207562 Cover Support Assembly  
(see page 10)  
237579 Air Control Kit  
237578 Cover Support Assembly  
Ref.  
No. Part No. Description  
Ref.  
No. Part No. Description  
101 203743 VALVE, restrictor  
Qty.  
Qty.  
201 190272 STUD, brace, left side  
202 190273 STUD, brace, left side  
203 190187 BRACKET, support, rear  
204 190181 BRACKET, riser tube  
205 158271 CLAMP, support  
206 202776 BRACE, support  
207 100268 SCREW, rd hd machine; 10-24 x  
3/8” (10 mm) long  
208 112895 SCREW, cap, hex hd; 1/4-20; 3/4”  
(19 mm) long  
209 112944 SCREW, cap, button hd; 5/16-18;  
3/4” (19 mm)  
1
1
1
1
1
1
2
1
Includes items 56-59 (see page 10)  
102 202295 VALVE, push-pull  
Includes items 61-72 (see page 10)  
TUBE; nylon; 7 ft; purchase locally  
1
103  
1
2
1
2
1
2
104 103473 STRAP, tie wire  
105 190231 BRACKET, valve  
106 113208 FITTING, tube  
108 169969 FITTING, air, quick disconnect  
109 112896 SCREW, cap, hex hd; 1/4-20; 1/2”  
(13 mm) long  
2
2
2
110 104123 WASHER, lock, spring; 1/4” size  
111 104121 NUT, hex; 1/4-20  
2
2
210 100057 SCREW, cap, hex hd; 5/16-18; 3/4”  
(19 mm)  
211 108946 NUT, hex; 5/16-18  
212 100181 NUT, square; 5/16-18  
213 100214 WASHER, lock, spring; 5/16” size  
214 112894 SCREW, cap, hex hd; 5/16-18;  
SST  
2
2
2
2
215 112904 WASHER, lock, spring; 5/16; SST  
216 112900 NUT, square; 5/16-18; SST  
4
2
306287W  
13  
 
Notes  
Notes  
14  
306287W  
 
Dimensions  
Dimensions  
NOTE: For elevator height dimensions,  
refer to FIG. 2 and Installation on page 4.  
5.5"  
(140 mm)  
8.88"  
(225.9 mm)  
.056" (14.2 mm)  
06533  
306287W  
15  
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs  
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT  
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
For the latest information about Graco products, visit www.graco.com.  
For patent information, see www.graco.com/patents.  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 306287  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA  
Copyright 1964, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.  
Revision W, February, 2014  
 

Grace MP3 Docking Station SCN300W User Manual
Graco Car Seat PD141229A User Manual
Grizzly Staple Gun G6042 3 User Manual
Hampton Direct Router Appendix C User Manual
Harbor Freight Tools Biscuit Joiner 96067 User Manual
Heat Glo LifeStyle Indoor Fireplace GRAND I35 User Manual
HP Hewlett Packard Network Card HP SSL1016 User Manual
HP Hewlett Packard Personal Computer BQ472AA User Manual
HTC Tablet HTCFlyerP512 User Manual
IBM Mouse G Mouse GPS Receiver G Mouse MR User Manual