L
®
Graco is concerned about the safety of every child who uses one
are equally concerned about the safety of their children. There ar
help minimize the risk that a baby using one of our mobile activit
charge of the baby should always follow these rules.
Tot Wheels Entertainer
Activity Center
OWNER’S MANUAL
1. Never leave your baby unattended.
Model No. ______________
Serial No. ______________
Most accidents happen to children while they are unsupervised. A
the baby at all times keeping the baby under a watchful eye. Bec
speed and is eager to explore all sorts of potential hazards, direc
times. If you believe proper supervision of your baby cannot be g
which the baby cannot be adequately protected while using our m
and that you consider instead an activity center without wheels, s
Dear Customer,
Please fill in the model
and serial numbers
above from the label
on the underside of
the tray.
2. Properly prepare your baby’s play s
Potential hazards in the room must be removed or guarded again
mind that the mobile activity center gives the baby the ability to m
otherwise be possible. That means it’s important to prepare play
reach, and closing doors to keep the baby away from potential ha
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Stairs
Steps
Blind
Obje
Dang
Pots
Book
Bath
Swim
Any
Raised thresholds
Driveways and sidewalks
Ramps or inclines
Decks
Ranges, heaters, fireplaces, hot
liquids and other heat sources
Models 4430 and 4440 Series
Congratulations on your purchase
of a Graco® Tot Wheels Entertainer®
activity center!
•
Only your commitment to safety can give you
Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco®
Tot Wheels Entertainer® activity center is a
wise choice, promising many hours of
enjoyment for your baby.
When to use your Tot Wheels Entertai
Your baby should be able to sit unaided and be able to
support most of his/her body weight with his/her legs
(about 6 months old).
!
•
•
!
Both feet should be able to touch the floor.
Before using your activity center, please
take a few minutes to read this Owner’s
Manual. The short time you spend reading
these instructions will help you use your
activity center properly.
When NOT to use your Tot Wheels En
Do not use until your child can sit up alone.
When your child can walk unaided.
When your child reaches 30 lbs. in weight.
When your child has grown over 32 inches in height.
If your activity center has become broken or damaged.
If you haven’t prepared a safe play space for your baby.
!
!
!
!
!
Customer Satisfaction
!
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with us about your product, please contact our
Customer Service Department at 1-800-345-4109
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
Other things to avoid
!
Don’t lift or carry your baby in the activity center.
Don’t adjust the activity center with your baby in it.
Don’t use the activity center for commercial use.
Don’t use the activity center if it is broken or damaged.
!
!
!
Graco® activity centers have been designed with your child’s enjoym
by following these guidelines and using simple common sense. Let’s
© 2000 Graco 303-3-00 303199
2
To Attach Seat
To Attach Base
Step 1.
Step 1.
On playtray models,
remove playtray from
activity center tray by
unsnapping both side
tabs from under tray.
Place base on floor with wheels
down.
Step 2.
Open tubes of tray assembly
as shown until they latch.
Step 2.
With the tray assembly upside down and its front
facing you, pull up on one of the tube ends until the
tubes snap into the first height position.
Step 3.
Front tube has plastic “T” ends.
Tilt tray assembly as shown.
Insert one plastic “T” into slot
on the inside front of the base.
Repeat on opposite side, flexing
tube inward if needed to
Insert seat rod through hole in left bracket, then through
the tunnel of the seat.
Nut
engage the slot.
Right
bracket
Seat rod
inside seat
tunnel
Left
bracket
Step 4.
Bent end seated
in channel
Lower rear tube so holes
in ends of tube line up with
two holes in back of activity
center base.
Step 3.
Be sure that plastic “T” pieces
remain in their slots.
Now push the threaded end of the seat rod through the
right bracket hole. Turn the bent end of the rod so it fits
securely into the left bracket channel. Push it into place.
Step 5.
Place nut on seat rod threads and tighten securely with
wrench or pliers.
Insert pin into hole
as shown, through
tray tube, and out
through base hole
on the other side.
Step 4.
Insert the pegs on the seat
back into the four holes
located at the rear of the tray.
Plastic pegs
Push
Underneath the tray,
insert the four screws
into the centers of the
pegs. Press down on
the seat back to help the
screws connect with
pegs. Tighten the
screws securely,
but do not
Press firmly until tab
snaps over head of pin.
Repeat on other side.
Bottom of
seat back
Be sure all parts of tray
and base are securely
fastened, with “T” pieces
in their slots and tabs
holding pins firmly.
Tab holds
pin
overtighten.
Head
of pin
303-3-00 303199
5
6
To Attach Decal(s)
To Use Parking Stands
(on certain models)
Place Graco® decal on front
of the tray as shown. Some
models also include a decal
for the base. Rub over
decal(s) with hand or clean
cloth to assure adhesion.
To install parking stands (two in
the front and one in the back), lift
base slightly, depress button on
front of stands and push stands
up until they snap into place.
To use parking stands, lift base
slightly and push stands down
until they snap into place.
To release parking stands, lift
base slightly and depress button
on front of stands. Push stands
upward into storage position.
To Adjust the Activity Center
Remove your child from the activity
center before making any adjustments.
!
When parking stands are in use, it is still possible
for your child to move the activity center.
Step 1.
!
!
Be sure to engage both parking stands.
To raise your activity center,
hold the base with one hand
while lifting the tray with the
other hand.
!
Never place the activity center on a table or
countertop.
!
Adjust the tray so that it is no
lower than waist level when
your child is standing in the
activity center.
Friction Strip Feature
Avoid
serious injury or death.
DO NOT use product
without the five friction
strips under the base.
Step 2.
To lower (or fold) your activity
center, reach underneath the
tray and squeeze the finger
latches, holding them in
while you lower the tray.
Tray should lower easily.
DO NOT force tray down or
unit could be damaged.
!
Make sure strips are
kept clean.
!
!
Clean strips with
WATER ONLY.
!
Friction strips under base
Caring for the Activity Center
Make sure five friction strips under base are kept
clean. Clean with water only.
For cleaning vinyl seat, metal and plastic parts
other than friction strips, use only household soap
or detergent and warm water. NO BLEACH.
Excessive exposure to sun or heat could cause
fading or warping of parts.
7
8
To Assemble the Playtray
(on certain models)
Music key (3)
Stickers
Do not install the playtray while
your baby is in the activity center.
CHECK that you have all the parts
listed at right before assembling your
playtray.
Teether and
stalk (style
may vary)
Steering wheel
and cap
Phone
and cord
Bar, two beads,
one ring
Step 1.
Insert teether
stalk into the
small square
hole in the tray.
Assemble the toys on the tray as shown.
Push and twist the ring and
two beads onto the toy bar.
Snap the toy bar into the holes
in the playtray; slight curve in
toy bar must curve away from
steering wheel. Be sure both
ends of the toy bar are firmly
snapped into the playtray.
Once the toy bar is inserted into
the playtray, you will not be able
to remove it.
Remove and DISCARD pull
tab from printed circuit board.
Then snap music keys in
place over the circuit board.
Place three stickers on front of
tray as shown. Rub over
stickers with hand or clean
cloth to assure adhesion.
Push wheel cap
onto steering wheel,
then push assembly
into large hole in
tray. Check that all
four tabs go into
hole in tray.
Push end of phone cord
through small hole in tray,
then tie a knot under the tray.
Pull on phone cord to make
sure cord is secure.
Step 2.
Step 4.
Line up front of
playtray with
front edge of
activity center
tray as shown.
CHECK that playtray is secure
on activity center by pulling up
on playtray.
Do not lift this
product by the playtray.
To Remove the Playtray
Step 3.
To remove tray, pull the two
side tabs outward, and lift up
playtray.
Push playtray down so both
side tabs snap under the
activity center tray.
303-3-00 303199
9
10
®
Step 4.
To Assemble the Mix ’N Move
Toy Gym (on certain models)
Insert the two prongs on a toy
base into a cap at the notches.
Before assembling, check that you have all the parts
listed below:
Step 5.
Turn toy base one quarter turn
until you feel the toy snap into
place. Check that toy is firmly
inserted by pulling on the toy.
Mix ’N Move® toys
(styles may vary)
Toy is removable (turn it the
other way with a little pressure)
so that you can replace it with
other toys when desired (sold
separately—see the enclosed
leaflet).
Mounting
post
and cap
(2 each)
Bar and beads
To Attach the Spoiler
(on certain models)
Step 1.
To mount beads on bar: flatten
ring at one end of bar as
shown and push through
hole in center of each bead.
Line up the pegs on the
bottom of the spoiler with
the two holes at the back of
the activity center and push
the spoiler in until it snaps
in place. It will not be
removable.
Shorter teeth
on bottom
Step 2.
Place ring on top of
a mounting post.
Shorter teeth must
be on the bottom, as
Do not allow spoiler to
block seat by inserting it
backwards.
Avoid falls and other hazards. Never
allow unit to be pushed while child is in product.
shown. Top of mounting
post will be even with top
of ring. Snap cap into place
inside mounting post and turn
it up to one half turn until it
locks in place. Repeat with
the other ring, post and cap.
Step 3.
Mount posts onto front
corners of activity center
tray as shown until they snap
securely into place. Center of
bar should curve away from
the seat, not toward it.
11
12
Replacement Parts
Instructions for ordering activity center parts:
Complete form below. Your activity center model
number MUST be included on the form to ensure proper
replacement parts. Your model number can be found
on a sticker on the underside of the tray. Payment
must accompany your order.
Parts List:
Price:**
Tray ........................................$15.00
Seat ........................................$13.00
Rear wheel .............................$8.00 (each)
Seat rod/nut ...........................$7.00
Caster ....................................$5.00 (each)
Hardware ................................$5.00
Pin ..........................................no charge
Parking stand* ........................$5.00 (each)
Mix ’N Move toy gym* ............$18.00
Mix ’N Move star*....................$8.00
Mix ’N Move spinning rings*....$8.00
Playtray with all toys* .............$20.00
* Certain models only
** Prices subject to change without notice.
IF YOU NEED HELP
If you have any questions or if you need any part
not listed, please call toll-free:
1-800-345-4109
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
ELVERSON, PA 19520
Model No. (required)
SHIP TO:
Name
Serial No. (required)
Address
Tray
Seat
Rear wheel
Seat rod/nut
Caster
Hardware
Pin
City, State, Zip
(
)
Telephone
Parking stand
Toy gym
Star
Spinning rings
Playtray with toys
Check enclosed
(payable to Graco Children’s
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Subtotal:
Shipping
& handling*:
Account #:
$5.00
6% sales tax
(PA only):
Total:
Expiration date:
Signature:
*$15.00 outside the continental U.S.
303-3-00 303199
13
|